Kit I2C analog output...
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
Digital display for six 0-30V analog values for connection to the analog output card.
With the rotary switch to select between 6 readings. The voltage is then displayed on the digital display with two decimal places.
The channels 1-5 are connected to the lower terminal block. The channel 6 is located on top of the banana 2.6mm jack. Here, an analog value from another card to be measured.
Supply voltage: 12V
Dimension of the printed circuit board 42 mm x 63 mm
1 | circuit board SIM-VM_LP lead-free tinned with solder resist |
1 | resistors 100 kohm |
1 | rotary selector switch 6x2 + button |
1 | 4-digit panel meter blue LED |
1 | built-in socket, 2.6mm, red + plug |
1 | built-in socket, 2.6mm, black + plug |
1 | terminal 2 pol. fix or plug in |
1 | terminal 6 pol. fix or plug in |
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Kit simulator module for 8 digital signals (8-bit) for DIN-rail mounting setpoint adjuster for eight digital signals for connection to the digital input card.
Simulator module for 5 alalog signals for DIN-rail mounting setpoint adjuster for five 0-10V analog signals for connection to the analogue input card
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit I2C switch for DIN rail mounting The I2C switch it is possible to switch four I2C buses in any combination to a master. Also its possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
Simulator module for 5 alalog signals for DIN-rail mounting setpoint adjuster for five 0-10V analog signals for connection to the analogue input card
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Kit simulator module for 8 digital signals (8-bit) for DIN-rail mounting setpoint adjuster for eight digital signals for connection to the digital input card.
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
With the I2C-USB mode, you can access I2C slaves via the PC. The kit includes all required components and the printed circuit board on which the FTDI SMD chip is already installed.
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Digital I2C output card with optocouplers8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The output driver TBD62783APG switches a positive voltage up to 30V.
Switching power supply 5V / 3A In: 200-240V / 50-60 HzOut: 5 V DC / 3 A
Digital I2C output card for AC voltage 24V AC / 1Awith optocoupler and triac 8-bit for DIN rail With the I2C output card, 8 digital AC power consumers can be switched.
Smart Card with I2C-bus EEprom memory 256 bytes (2k bit) Chip: ST14C02/X24026 ISO format 85.7 x 54 x 0.81 mm
Plug-in switching power supply 5 V / 2 A In: 100-240V / 50-60 HzOut: 5 V / 2 A Dimensions (LxWxH): 80 x 32 x 42 mm + connector contacts Connecting cable 1.5 m with 5.5 pin barrel connectors diameter 2,1 mm center positive.
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Kit switching power supply control board 3,3V 5V 9V 10V 15V 24V / 2,5A for DIN-Rail This switched-mode power supply board can be used to supply the I2C modules or other devices with power.
Simulator module for 5 alalog signals for DIN-rail mounting setpoint adjuster for five 0-10V analog signals for connection to the analogue input card
Kit I2C analog input card 4 channel 18 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V +-10V +-2V or 0-20mA can be read.
Kit I2C analog input card 8 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit switching power supply control board 5V / 2,5A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Connection cable PG7xx to S5 CPU 5 meters Simatic S5 interface cable for SIMATIC - PG 7xx to the S5 CPU Identical to 6ES5734-2BF00 Length 5 metersother lengths on request