Kit I2C Input card 8 Bit
Kit I2C digital input board 8-bit with optocoupler and latch All components including the PCB
The kit includes all required components and the circuit board.
With the I2C buffer module you can test the function of the module P82B96 without large amount of soldering.
The buffer can be constructed according to the data of the P82B96 bus lines to 200 meters.
To Take a look at the description AN255-02.pdf on page 13
At the other end sits back a buffer of the "high-strung" level again brings back to standard I2C. Then can be interconnected as many slaves again.
Dimensions of the circuit board 40 x 30 mm.
More information here:: I2C-Buffer breakout board P82B96
1 | circuit board I2BU-LP |
1 | I2C-Buffer P82B96 + IC socket 8 pin |
1 | SCHOTTKY Diode BAT 54A SMD |
1 | Ceramic Capacitor 100 nF |
2 | Ceramic Capacitor 220 pF |
2 | pin connectors 3 pol and Jumper |
2 | terminal 4pol. |
1 | terminal 2pol. |
2 | resistor 750 Ohm |
2 | resistor 4,7 k |
Manufacturer information
Responsible person for the EU
Horter & Kalb
Jürgen Horter
Klinikumallee 23
)5445 Bayreuth
mail@horter.de
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Kit I2C digital input board 8-bit with optocoupler and latch All components including the PCB
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Digital I2C output card with optocouplers8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The output driver TBD62783APG switches a positive voltage up to 30V.
Kit I2C analog input card 8 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Longer I2C bus wires with the P82B715 The kit includes all required components and the circuit board.
Mounting clip for DIN rail Rittal SZ 2309.000 inkl. Screws M4 x 10
Precision measuring resistor 500 Ohm 0.1% 0.4W With this resistor, a current signal 0-20mA can be converted into a voltage signal 0-10V.Conversion 0-20mA signal in 0-10VConversion 4-20mA signal in 2-10VThe voltage can then be measured with the analog card.
Kit switching power supply control board 5V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Stacking Header 2 x 13 pin for I2C-Repeater Accessories for I2C-Repeater I2RPI+T-FG
Galvanic isolation of I2C buses with ADUM 1250 The kit includes all required components and the circuit board.
Breakoutboard with I2C Calendar & Clock PCF 8583 The kit includes all required components and the circuit board.
Kit I2C-Repeater for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Longer I2C bus wires with the P82B715 The kit includes all required components and the circuit board.
The I2C-coupler converts the V24 signals of the serial interface (RS232) in 5V signals for the I2C hardware. The kit includes all required components and the circuit board.
I2C digital output board without amplifiers If you want to have mixed the output stages ( eg 2 Ralais and 6 transistors)You can order the basic components here and the output stages separately below in the shop
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Kit I2C input card digital 8-bit 5-24V for DIN rail With the I2C input module you can read 8 digital signals up to 30V.
I2C output board with relay output stages 8- bit digital All components required for the I2C output board including 8 single-line relay 5V with integr. Free-wheeling diode. Switching capacity max. 200V AC 15W
Kit switching power supply control board 5V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Kit switching power supply control board 3,3V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Simulator Panel Voltmeter Module 6 analog measurements 0-30V Digital display for six 0-30V analog values for connection to the analog output card.
I2C output board with transistor amplifiers 8- bit digital All components required for the I2C output board including 8 power transistors BD135 (invers) or BD136 (normal) Switching capacity max. 45V 1.5A
Digital I2C input card with optocouplers 8-bit 5-24V for DIN rail The I2C input module can be used to read 8 digital signals from 2.5V to 30V via the I2C bus. The inputs are galvanically isolated with optocouplers