Set I2C bus connector 5pol
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
The kit includes all required components and the circuit board.
With the I2C Calendar & Clock PCF8583P it is possible to realize a Quartz Accurate real-time clock for the I2C bus.
It can also be counted fast pulses and read via the I2C bus.
On the board with a jumper between the clock (32768Hz quartz) and counter can be switched.
Dimensions of the circuit board 40 x 30 mm.
Data Sheet
Schematic Diagram
PCF8583-Datasheet
1 | circuit board I2CC-LP |
1 | PCF8583P + IC socket 8 pin |
1 | NE555 + IC socket 8 pin |
1 | resistor 270 Ohm |
1 | resistor 10 k Ohm |
1 | resistor 470 kOhm |
1 | resistor 4,7 kOhm |
1 | LED 3mm 20mA |
1 | quartz 32,768 MHz |
2 | Ceramic Capacitor 100 nF |
1 | Trimm Capacitor 4 - 40pF |
1 | Ceramic Capacitor 27 pF |
1 | Ceramic Capacitor 10 nF |
1 | Elko 10 yF |
2 | Pin header 3-pole 3pol + Jumper |
1 | terminal 6pol. |
Manufacturer information
Responsible person for the EU
Horter & Kalb
Jürgen Horter
Klinikumallee 23
)5445 Bayreuth
mail@horter.de
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Digital I2C output card with optocouplers8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The output driver TBD62783APG switches a positive voltage up to 30V.
Set I2C connection cable 5pol Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AIN18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Kit I2C ARDUINO module for "Arduino Pro Micro" on DIN rail Put the "ARDUINO Pro Micro" on the top-hat rail and write your own applications as an I2C master or I2C slave.
Kit I2C-Repeater for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit switching power supply control board 3,3V 5V 9V 10V 15V 24V / 2,5A for DIN-Rail This switched-mode power supply board can be used to supply the I2C modules or other devices with power.
Digital I2C input card with optocouplers 8-bit 5-24V for DIN rail The I2C input module can be used to read 8 digital signals from 2.5V to 30V via the I2C bus. The inputs are galvanically isolated with optocouplers
Kit switching power supply control board 5V / 2,5A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Kit I2C switch for DIN rail mounting The I2C switch it is possible to switch four I2C buses in any combination to a master. Also its possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Kit I2C analog input card 4 channel 18 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V +-10V +-2V or 0-20mA can be read.
Kit I2C I2C-RS232-Modem 2 for DIN rail With this modemyou can control or read I2C slaves via the serial RS232 interface. The baud rate adjustable via PC software. Command Set is the same as the I2C-USB modem
For communication to I2C commands as ASCII control sequences via the COM interface send and receive. The kit includes all required components and the circuit board. All prices include VAT plus shipping costs.Delivery time 2-3 daysPrice changes and errors excepted.
Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Digital I2C output card with optocouplers8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The output driver TBD62783APG switches a positive voltage up to 30V.
I2C output board with relay output stages 8- bit digital All components required for the I2C output board including 8 single-line relay 5V with integr. Free-wheeling diode. Switching capacity max. 200V AC 15W
With the I2C-USB mode, you can access I2C slaves via the PC. The kit includes all required components and the printed circuit board on which the FTDI SMD chip is already installed.
Kit switching power supply control board 3,3V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Simulator Panel Voltmeter Module 6 analog measurements 0-30V Digital display for six 0-30V analog values for connection to the analog output card.
Kit I2C ARDUINO module for "Arduino Pro Micro" on DIN rail Put the "ARDUINO Pro Micro" on the top-hat rail and write your own applications as an I2C master or I2C slave.