Mounting frame
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
With the I2C output card 8 digital loads can be switched.
The output driver turns UDN2981 a positive voltage up to 30V.
With the I2C output card 8 digital loads can be switched. The output driver UDN2981 turns a positive voltage up to 30V.
The signal states are displayed on eight low-current LEDs.
The circuit uses negative logic because the I2C Port Expander module PCF8574 by switches on all outputs at voltage.
When controlling only the desired bit pattern must be inverted. Or subtracting from 255 the desired output value before it is transferred to the output card.
Size of the circuit board 42 mm x 63 mm
For more information about this product can be found on the product page i2c-ouput-modul.
1 | circuit board I2HA_LP lead-free tinned with solder resist |
1 | Resistor network 8x 1,5k |
8 | LED 3mm 2mA green |
2 | Ceramic Capacitor 100 nF |
1 | PCF8574P oder PCF8574A + IC socket 16 pin |
1 | 74AC540N + IC-socket 20 pin |
1 | UDN2981A Darlington-Array + IC-socket 18 pin |
3 | pin connectors 3 pol and Jumper |
1 | terminal 4 pol. |
1 | terminal 10 pol. |
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Kit switching power supply control board 3,3V 5V 9V 10V 15V 24V / 2,5A for DIN-Rail This switched-mode power supply board can be used to supply the I2C modules or other devices with power.
Kit simulator module for 8 digital signals (8-bit) for DIN-rail mounting setpoint adjuster for eight digital signals for connection to the digital input card.
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Kit switching power supply control board 5V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
I2C Analog-to-Digital Converter - ADC 18B delta-sigma ADC dual Ch 4sp
I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit I2C analog input card 4 channel 18 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V +-10V +-2V or 0-20mA can be read.
Kit I2C ARDUINO module for "Arduino Pro Micro" on DIN rail Put the "ARDUINO Pro Micro" on the top-hat rail and write your own applications as an I2C master or I2C slave.
I2C pulse counter kit with PCF8583 and optocoupler 2-channel counter for fast pulses
Programmed PIC for our analog output module 5 channel 10 bit (I2HAA-Bk)
Digital I2C input card with optocouplers 8-bit 5-24V for DIN rail The I2C input module can be used to read 8 digital signals from 2.5V to 30V via the I2C bus. The inputs are galvanically isolated with optocouplers
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Digital I2C output card with optocouplers8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The output driver TBD62783APG switches a positive voltage up to 30V.
Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit simulator module for 8 digital signals (8-bit) for DIN-rail mounting setpoint adjuster for eight digital signals for connection to the digital input card.
Kit switching power supply control board 5V / 2,5A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Kit I2C analog input card 8 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit I2C-Repeater for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit switching power supply control board 5V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
I2C pulse counter kit with PCF8583 and optocoupler 2-channel counter for fast pulses
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit I2C ARDUINO module for "Arduino Pro Micro" on DIN rail Put the "ARDUINO Pro Micro" on the top-hat rail and write your own applications as an I2C master or I2C slave.
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Kit I2C analog input card 4 channel 18 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V +-10V +-2V or 0-20mA can be read.
I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL