Mounting frame
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
With this modemyou can control or read I2C slaves via the serial RS232 interface. The baud rate adjustable via PC software.
Command Set is the same as the I2C-USB modem
The faster PIC from the I2C-USB modem with the extended instruction set, we have now incorporated in this new I2C-RS232 modem.
Can now via the RS232 interface, for example, and PLC controls access with a serial interface to the I2C bus.
The baud rate adjustable via PC software.
Size of the circuit board 42 mm x 63 mm
For more information about this product can be found on the product page i2c-RS232-Modem-2
http://www.horter.de/doku/i2c-hs-modem_sp.pdf
1 | circuit board I2HM_LP lead-free tinned with solder resist |
1 | Resistor network 4x 4,7kOhm - 8 Pin |
1 | Resistor network 4x 1,5kOhm - 4 Pin |
1 | LED 3mm 2 mA green |
1 | LED 3mm 2 mA yellow |
1 | LED 3mm 2 mA red |
2 | Ceramic Capacitor 27 pF |
4 | Elko 10 yF 16V |
2 | Ceramic Capacitor 100 nF |
1 | PIC18F1320P programmed + IC-socket 18 pin |
1 | MAX232 + IC-socket 16 polig |
1 | Quarz 10 MHz |
2 | pin connectors 3 pol and Jumper |
1 | terminal 6 pol. |
1 | SUB-D 9 female print montage |
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Digital I2C input card with optocouplers 8-bit 5-24V for DIN rail The I2C input module can be used to read 8 digital signals from 2.5V to 30V via the I2C bus. The inputs are galvanically isolated with optocouplers
Digital I2C output card with optocouplers8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The output driver TBD62783APG switches a positive voltage up to 30V.
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Set I2C connection cable 5pol Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AIN18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.
With the I2C-USB mode, you can access I2C slaves via the PC. The kit includes all required components and the printed circuit board on which the FTDI SMD chip is already installed.
Plug-in switching power supply 5 V / 1 A In: 100-240V / 50-60 Hz 0.15 A Out: 5 V / 1 A Dimensions (LxWxH): 70 x 35 x 25 mm + connector contacts Connecting cable 1.5 m with barrel connector 5.5 pin diameter 2.1mm center positive.
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Stacking Header 2 x 20 pin for I2C-Repeater Accessories for I2C-Repeater I2RPI+T-FG
Longer I2C bus wires with the P82B715 The kit includes all required components and the circuit board.
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
Kit switching power supply control board 3,3V 5V 9V 10V 15V 24V / 2,5A for DIN-Rail This switched-mode power supply board can be used to supply the I2C modules or other devices with power.
Finish machined case for I2C-USB modem. The holes for the LEDs and the power supply are drilled. Furthermore millings for the tub and plug the USB connector are made on both sides.
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Kit I2C-Repeater for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Mounting clip for DIN rail Rittal SZ 2309.000 inkl. Screws M4 x 10
Kit I2C radio transmitter for DIN rail mounting this 433 MHz radio transmitter allows you remote-controlled electrical socket controlled via the I2C bus.
Kit switching power supply control board 5V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
I2C pulse counter kit with PCF8583 and optocoupler 2-channel counter for fast pulses
Kit switching power supply control board 3,3V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit I2C analog input card 8 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit I2C switch for DIN rail mounting The I2C switch it is possible to switch four I2C buses in any combination to a master. Also its possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Simulator module for 5 alalog signals for DIN-rail mounting setpoint adjuster for five 0-10V analog signals for connection to the analogue input card
Kit I2C ARDUINO module for "Arduino Pro Micro" on DIN rail Put the "ARDUINO Pro Micro" on the top-hat rail and write your own applications as an I2C master or I2C slave.
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Digital I2C output card with optocouplers8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The output driver TBD62783APG switches a positive voltage up to 30V.