Mounting frame
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
This 5V switching power supply control board I2C modules can be supplied with power.
The maximum input voltage range of the built-in switching regulator MC34063 is 40V and delivers up to 1.5 A.
In the control cabinet so that you can generate the 5V voltage for the I2C modules from the most existing 24V DC.
Size of the circuit board 42 mm x 63 mm
1 | circuit board I2HN_LP lead-free tinned with solder resist |
1 | Resistor 0,33 Ohm |
1 | Resistor 1,2 kOhm |
1 | Resistor 1,5 kOhm |
1 | Resistor 3,6 kOhm |
1 | LED green 3mm 2 mA |
1 | Rectifier diode 1N4007 |
1 | Schottky Diode 1N5819 |
1 | Elko 100 yF / 63V |
1 | Ceramic Capacitor 470 pF |
1 | Elko 470 yF 25V |
1 | MC34063AP switching regulator + IC-socket 8 pin |
1 | inductance 220 yH |
1 | fuse holder + fuse 1,0 A medium time-lag |
2 | terminal 2 pol. |
Manufacturer information
Responsible person for the EU
Horter & Kalb
Jürgen Horter
Klinikumallee 23
)5445 Bayreuth
mail@horter.de
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Kit switching power supply control board 5V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C input card digital 8-bit 5-24V for DIN rail With the I2C input module you can read 8 digital signals up to 30V.
Simulator module for 5 alalog signals for DIN-rail mounting setpoint adjuster for five 0-10V analog signals for connection to the analogue input card
Set I2C connection cable 5pol Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AIN18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
I2C master kit with ARDUINO-UNO and optional W5500 LAN on DIN rail Compact I2C master with an "Arduino UNO" for the DIN rail. The module can be used to implement a variety of applications with the Arduino IDE or with Platform IO. For example: - I2C Modbus-TCP Server- I2C MQTT Client /...
Kit I2C analog input card 8 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.
Kit I2C radio transmitter for DIN rail mounting this 433 MHz radio transmitter allows you remote-controlled electrical socket controlled via the I2C bus.
Kit switching power supply control board 3,3V 5V 9V 10V 15V 24V / 2,5A for DIN-Rail This switched-mode power supply board can be used to supply the I2C modules or other devices with power.
Digital I2C output card with optocouplers8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The output driver TBD62783APG switches a positive voltage up to 30V.
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Simulator Panel Voltmeter Module 6 analog measurements 0-30V Digital display for six 0-30V analog values for connection to the analog output card.
Kit I2C analog input card 4 channel 18 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V +-10V +-2V or 0-20mA can be read.