Mounting frame
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
The I2C input module can be used to read 8 digital signals from 2.5V to 30V via the I2C bus.
The inputs are galvanically isolated with optocouplers
With the I2C input module, 8 digital signals, e.g. Of switches or sensors.
The signal states are indicated on 8 low-current LEDs, the HIGH level is detected between 2.5 and 30 V depending on the used resistor network.
If a signal is changed at an input, this is indicated by a red LED and the INT signal is pulled to LOW.
The I2C modem recognizes this signal change and can also automatically query all input cards.
Dimension of the circuit board 42 mm x 63 mm
The input voltage range of the card can be adapted using the resistance network RBV.
Uin: 2,5 - 13V 1,5 kOhm (Please order separately! Article I2EOK-RV)
Uin: 10 - 24V 4,7 kOhm (Standard, Liegt dem Bausatz bei)
Uin: 12 - 30V 10 kOhm (Please order separately! Article I2EOK-RV)
1 | circuit board IEOK_LP lead-free tinned with solder resist |
1 | Resistor 1,5 kOhm |
2 | Resistor 4,7 kOhm |
2 | Resistor 10 kOhm |
1 | Resistor network RNV Uin: 10 - 24V 4,7 kW |
1 | Resistor network 8x 1,5k |
1 | Resistor network 8x 4,7k |
8 | LED 3mm 2mA green |
1 | LED 3mm 2mA red |
1 | Ceramic Capacitor 100 nF |
2 | NPN-Transistor BC546A |
1 | PCF8574P oder PCF8574A + IC socket 16 pin |
2 | Opto coupler TLP293-4 soldered |
3 | pin connectors 3 pol and Jumper |
1 | terminal 5 pol. |
1 | terminal 10 pol. |
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Set I2C connection cable 5pol Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AIN18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Kit switching power supply control board 5V / 2,5A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Kit I2C input card digital 8-bit 5-24V for DIN rail With the I2C input module you can read 8 digital signals up to 30V.
Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit I2C analog input card 4 channel 18 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V +-10V +-2V or 0-20mA can be read.
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Precision CMOS rail-to-rail input and output op amps
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Table power supply 5 V / 4 A In: 100-240V / 50-60 Hz, 1 A maxOut: 5 V / 4 A
Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.
Power cord for AC-Adapter black - length 1,4 m or 1,8 mCable cross-section 3x 0.75 mm² Load limit 6 A
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit switching power supply control board 5V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Kit I2C input card digital 8-bit 5-24V for DIN rail With the I2C input module you can read 8 digital signals up to 30V.
Kit I2C ARDUINO module for "Arduino Pro Micro" on DIN rail Put the "ARDUINO Pro Micro" on the top-hat rail and write your own applications as an I2C master or I2C slave.
Kit I2C analog input card 4 channel 18 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V +-10V +-2V or 0-20mA can be read.
Kit switching power supply control board 5V / 2,5A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Kit I2C analog input card 8 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Mounting clip for DIN rail Rittal SZ 2309.000 inkl. Screws M4 x 10
Kit switching power supply control board 3,3V 5V 9V 10V 15V 24V / 2,5A for DIN-Rail This switched-mode power supply board can be used to supply the I2C modules or other devices with power.
Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.
Kit I2C I2C-RS232-Modem 2 for DIN rail With this modemyou can control or read I2C slaves via the serial RS232 interface. The baud rate adjustable via PC software. Command Set is the same as the I2C-USB modem
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
I2C pulse counter kit with PCF8583 and optocoupler 2-channel counter for fast pulses