With the I2C analog input card 5 analog signals of 0-10 V can be read.
The analog-in card has a total of 8 A/D converter with a resolution of 10 bit. The analog-in card is completely controlled register. All data is stored in readable and writable registers.
Controls all operations on the map by a microcontroller (PIC 18F13K22). This establishes the connection between the I2C bus and the A / D converters. It ensures that the data is updated in the registers with a frequency of 250 Hz.
The minimum value of a register is 0 × 0000 (dec. 0) the Maximum 0x03FF (dec. 1023). The A / D converter to measure against an internal reference voltage of 2.048 volts. Therefore corresponds to the maximum value of a measurable voltage of 2.048 volts at the input. With appropriate input resistors can be the measuring area of the map to expand.
The board can be connected via the bus connector.
Size of the circuit board 42 mm x 63 mm
Program examples, see the blog post I2C-Analog Input 8 Kanäle 0-10V 10 Bit.
| 1 | PCB I2AE8_LP lead-free tinned with solder resist |
| 8 | precision resistor 120 kOhm 0,1% |
| 8 | precision resistor 30 kOhm 0,1% |
| 8 | tantalum capacitor 0.1 yF |
| 1 | ceramic capacitor 100 nF |
| 1 | I2C-AE8-PIC programmed |
| 1 | IC socket 20 pin |
| 3 | pin connectors 3 pol and Jumper |
| 1 | terminal 4 pol. |
| 1 | terminal 10 pol. |
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Simulator module for 5 alalog signals for DIN-rail mounting setpoint adjuster for five 0-10V analog signals for connection to the analogue input card
Programmed PIC for our analog input module 8 channel 10 bit 250Hz (I2AE8-Bk)
Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.
Kit I2C I2C-RS232-Modem 2 for DIN rail With this modemyou can control or read I2C slaves via the serial RS232 interface. The baud rate adjustable via PC software. Command Set is the same as the I2C-USB modem
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Digital I2C output card with optocouplers8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The output driver TBD62783APG switches a positive voltage up to 30V.
Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Kit I2C-Repeater for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C analog input card 4 channel 18 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V +-10V +-2V or 0-20mA can be read.
Mounting clip for DIN rail Rittal SZ 2309.000 inkl. Screws M4 x 10
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
Kit I2C switch for DIN rail mounting The I2C switch it is possible to switch four I2C buses in any combination to a master. Also its possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit switching power supply control board 3,3V 5V 9V 10V 15V 24V / 2,5A for DIN-Rail This switched-mode power supply board can be used to supply the I2C modules or other devices with power.
