Mounting frame
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
With the I2C analog input card 5 analog signals of 0-10 V +-10V +-2V or 0-20mA can be read.
In this card we have installed an AD converter from Microchip. This can read in 4 analog values with a maximum resolution of 18 bits.
The following measuring ranges are possible:
By changing the series resistors can also be other measuring ranges, e.g. 0-30V to monitor on-board voltages in the vehicle, boat or caravan.
The board can be connected via the bus connector.
Size of the circuit board 42 mm x 63 mm
Program examples, see the follow blog post:
I2C-Analog-Input 4 Kanäle / 18 Bit mit MCP3424
1 | PCB I2AE18_LP lead-free tinned with solder resist |
4 | precision resistor 120 kOhm 0,1% |
4 | precision resistor 30 kOhm 0,1% |
4 | precision resistor 500 Ohm 0,1% |
4 | tantalum capacitor 0.1 yF |
1 | ceramic capacitor 100 nF |
1 | MCP3424 SO-14 |
1 | pin connectors 40 pol |
10 | Jumper |
1 | terminal 4 pol. |
1 | terminal 8 pol. |
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Simulator module for 5 alalog signals for DIN-rail mounting setpoint adjuster for five 0-10V analog signals for connection to the analogue input card
Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Set I2C connection cable 5pol Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AIN18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Kit I2C input card digital 8-bit 5-24V for DIN rail With the I2C input module you can read 8 digital signals up to 30V.
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.
Precision measuring resistor 500 Ohm 0.1% 0.4W With this resistor, a current signal 0-20mA can be converted into a voltage signal 0-10V.Conversion 0-20mA signal in 0-10VConversion 4-20mA signal in 2-10VThe voltage can then be measured with the analog card.
Set I2C connection cable 5pol Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AIN18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
I2C Analog-to-Digital Converter - ADC 18B delta-sigma ADC dual Ch 4sp
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Kit I2C I2C-RS232-Modem 2 for DIN rail With this modemyou can control or read I2C slaves via the serial RS232 interface. The baud rate adjustable via PC software. Command Set is the same as the I2C-USB modem
Longer I2C bus wires with the P82B715 The kit includes all required components and the circuit board.
Digital I2C input card with optocouplers 8-bit 5-24V for DIN rail The I2C input module can be used to read 8 digital signals from 2.5V to 30V via the I2C bus. The inputs are galvanically isolated with optocouplers
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Kit I2C ARDUINO module for "Arduino Pro Micro" on DIN rail Put the "ARDUINO Pro Micro" on the top-hat rail and write your own applications as an I2C master or I2C slave.
Set I2C connection cable 5pol Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AIN18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Digital I2C output card for AC voltage 24V AC / 1Awith optocoupler and triac 8-bit for DIN rail With the I2C output card, 8 digital AC power consumers can be switched.
Kit I2C analog input card 8 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit I2C radio transmitter for DIN rail mounting this 433 MHz radio transmitter allows you remote-controlled electrical socket controlled via the I2C bus.
Simulator module for 5 alalog signals for DIN-rail mounting setpoint adjuster for five 0-10V analog signals for connection to the analogue input card
Digital I2C input card with optocouplers 8-bit 5-24V for DIN rail The I2C input module can be used to read 8 digital signals from 2.5V to 30V via the I2C bus. The inputs are galvanically isolated with optocouplers