Mounting frame
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
This 5V switching power supply control board I2C modules can be supplied with power.
The maximum input voltage range of the built-in switching regulator LM 2576 is 40V and delivers up to 3 A.
In the control cabinet so that you can generate the 5V voltage for the I2C modules from the most existing 24V DC.
Size of the circuit board 42 mm x 63 mm
Data Sheet
Shematic Diagram
data sheet LM2576
1 | circuit board I2HN3_LP lead-free tinned with solder resist |
1 | Resistor 1,5 kOhm |
1 | LED green 3mm 2 mA |
1 | Rectifier diode 1N4007 |
1 | Schottky Diode SB360 |
1 | Elko 100 yF / 63V |
1 | Elko 1000 yF / 25V |
1 | LM 2576 3,3 5 12 15 oder ADJ |
1 | heatsink + screw M3x16 Spacing roller Ø 3 x 8 mm |
1 | inductance 100 yH / 3,2 A |
1 | fuse holder + fuse 2,5 A medium time-lag |
2 | terminal 2 pol. |
Manufacturer information
Responsible person for the EU
Horter & Kalb
Jürgen Horter
Klinikumallee 23
)5445 Bayreuth
mail@horter.de
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
W5500 TCP/IP Ethernet module for the I2C master with Arduino UNO
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Digital I2C output card with optocouplers8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The output driver TBD62783APG switches a positive voltage up to 30V.
Finish machined case for I2C-USB modem. The holes for the LEDs and the power supply are drilled. Furthermore millings for the tub and plug the USB connector are made on both sides.
Micro USB to TTL UART programming adapter 3.3V/5V with CP2102
I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C-Repeater for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C digital input board 8-bit with optocoupler and latch All components including the PCB
Precision measuring resistor 500 Ohm 0.1% 0.4W With this resistor, a current signal 0-20mA can be converted into a voltage signal 0-10V.Conversion 0-20mA signal in 0-10VConversion 4-20mA signal in 2-10VThe voltage can then be measured with the analog card.
Set I2C connection cable 5pol Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AIN18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
Digital I2C input card with optocouplers 8-bit 5-24V for DIN rail The I2C input module can be used to read 8 digital signals from 2.5V to 30V via the I2C bus. The inputs are galvanically isolated with optocouplers
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Kit I2C analog input card 4 channel 18 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V +-10V +-2V or 0-20mA can be read.
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Simulator Panel Voltmeter Module 6 analog measurements 0-30V Digital display for six 0-30V analog values for connection to the analog output card.
Mounting clip for DIN rail Rittal SZ 2309.000 inkl. Screws M4 x 10
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Digital I2C output card with optocouplers8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The output driver TBD62783APG switches a positive voltage up to 30V.
Kit I2C I2C-RS232-Modem 2 for DIN rail With this modemyou can control or read I2C slaves via the serial RS232 interface. The baud rate adjustable via PC software. Command Set is the same as the I2C-USB modem
Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.
Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit I2C ARDUINO module for "Arduino Pro Micro" on DIN rail Put the "ARDUINO Pro Micro" on the top-hat rail and write your own applications as an I2C master or I2C slave.
Digital I2C output card for AC voltage 24V AC / 1Awith optocoupler and triac 8-bit for DIN rail With the I2C output card, 8 digital AC power consumers can be switched.
Kit I2C analog input card 8 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit switching power supply control board 3,3V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Kit switching power supply control board 3,3V 5V 9V 10V 15V 24V / 2,5A for DIN-Rail This switched-mode power supply board can be used to supply the I2C modules or other devices with power.
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Kit simulator module for 8 digital signals (8-bit) for DIN-rail mounting setpoint adjuster for eight digital signals for connection to the digital input card.