ARDUINO Pro Micro 5 V / 16 MHz ATmega32U4
Kit I2C ARDUINO module for "Arduino Pro Micro" on DIN rail Put the "ARDUINO Pro Micro" on the top-hat rail and write your own applications as an I2C master or I2C slave.
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit simulator module for 8 digital signals (8-bit) for DIN-rail mounting setpoint adjuster for eight digital signals for connection to the digital input card.
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Kit I2C ARDUINO module for "Arduino Pro Micro" on DIN rail Put the "ARDUINO Pro Micro" on the top-hat rail and write your own applications as an I2C master or I2C slave.
Kit I2C input card digital 8-bit 5-24V for DIN rail With the I2C input module you can read 8 digital signals up to 30V.
Digital I2C output card with optocouplers8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The output driver TBD62783APG switches a positive voltage up to 30V.
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Simulator Panel Voltmeter Module 6 analog measurements 0-30V Digital display for six 0-30V analog values for connection to the analog output card.
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Breakoutboard with I2C Calendar & Clock PCF 8583 The kit includes all required components and the circuit board.
Kit I2C I2C-RS232-Modem 2 for DIN rail With this modemyou can control or read I2C slaves via the serial RS232 interface. The baud rate adjustable via PC software. Command Set is the same as the I2C-USB modem
Kit I2C radio transmitter for DIN rail mounting this 433 MHz radio transmitter allows you remote-controlled electrical socket controlled via the I2C bus.
Simulator Panel Voltmeter Module 6 analog measurements 0-30V Digital display for six 0-30V analog values for connection to the analog output card.
I2C pulse counter kit with PCF8583 and optocoupler 2-channel counter for fast pulses
Kit I2C ARDUINO module for "Arduino Pro Micro" on DIN rail Put the "ARDUINO Pro Micro" on the top-hat rail and write your own applications as an I2C master or I2C slave.
Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit simulator module for 8 digital signals (8-bit) for DIN-rail mounting setpoint adjuster for eight digital signals for connection to the digital input card.
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit switching power supply control board 5V / 2,5A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Digital I2C output card with optocouplers8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The output driver TBD62783APG switches a positive voltage up to 30V.
Kit I2C switch for DIN rail mounting The I2C switch it is possible to switch four I2C buses in any combination to a master. Also its possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit switching power supply control board 5V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.
