Mounting frame
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
2-channel counter for fast pulses
With the counter module, you can record fast pulses from flow sensors or other pulse generators and read them out periodically.
2 | Resistor network 3x 4,7 kOhm 6 Pins |
1 | Resistor network 6x 4,7k 7 Pins |
1 | Resistor network 4x 1,5k 5-Pins |
2 | series sesistor 5V=270 12V=560 24V=1,5k |
6 | Transistor BC546 |
2 | LED 3mm green 2mA |
2 | LED 3mm red 2mA |
2 | Ceramic capacitor100nF |
2 | pin connectors 3-pin + jumper |
2 | pin connectors 6-pin + jumper |
2 | PCF8583 + IC socket 8 polig |
1 | TLP521-2 + IC socket 8 polig |
1 | terminal 5 pol fest oder steckbar |
1 | terminal 6 pol fest oder steckbar |
1 | PCB lead-free tin with solder mask |
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Kit I2C input card digital 8-bit 5-24V for DIN rail With the I2C input module you can read 8 digital signals up to 30V.
Kit switching power supply control board 5V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Kit switching power supply control board 3,3V 5V 9V 10V 15V 24V / 2,5A for DIN-Rail This switched-mode power supply board can be used to supply the I2C modules or other devices with power.
Digital I2C output card for AC voltage 24V AC / 1Awith optocoupler and triac 8-bit for DIN rail With the I2C output card, 8 digital AC power consumers can be switched.
Mounting clip for DIN rail Rittal SZ 2309.000 inkl. Screws M4 x 10
Kit I2C analog input card 8 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.
Kit switching power supply control board 3,3V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Simulator module for 5 alalog signals for DIN-rail mounting setpoint adjuster for five 0-10V analog signals for connection to the analogue input card
Kit I2C analog input card 4 channel 18 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V +-10V +-2V or 0-20mA can be read.
Kit I2C input card digital 8-bit 5-24V for DIN rail With the I2C input module you can read 8 digital signals up to 30V.
Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Simulator Panel Voltmeter Module 6 analog measurements 0-30V Digital display for six 0-30V analog values for connection to the analog output card.
Digital I2C output card with optocouplers8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The output driver TBD62783APG switches a positive voltage up to 30V.
Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL