Case for I2C USB modem
Finish machined case for I2C-USB modem.
The holes for the LEDs and the power supply are drilled.
Furthermore millings for the tub and plug the USB connector are made on both sides.
Partlist:
1 | Case milled and drilled ready |
4 | Screws for attaching the printed circuit board |
1 | Sticker "I2C-USB Modem" |
1 | 50cm cable for the I2C side |
Specific References
- EAN13
- 4260404260516
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Customers who bought this product also bought:
Kit I2C-USB-Modem PC...
With the I2C-USB mode, you can access I2C slaves via the PC. The kit includes all required components and the printed circuit board on which the FTDI SMD chip is already installed.
Set I2C bus connector 5pol
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Kit I2C EEprom test board
Describe and read I2C EEPROMs. The kit includes all required components and the circuit board.
Kit I2C Output 24V 1A with...
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Set I2C connection cable 5pol
Set I2C connection cable 5pol Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AIN18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Kit I2C digital input...
Digital I2C input card with optocouplers 8-bit 5-24V for DIN rail The I2C input module can be used to read 8 digital signals from 2.5V to 30V via the I2C bus. The inputs are galvanically isolated with optocouplers
Kit simulator module for 8...
Kit simulator module for 8 digital signals (8-bit) for DIN-rail mounting setpoint adjuster for eight digital signals for connection to the digital input card.
Mounting frame
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
9 other products in the same category:
Kit I2C RS232 Modem 2 / PC...
Kit I2C I2C-RS232-Modem 2 for DIN rail With this modemyou can control or read I2C slaves via the serial RS232 interface. The baud rate adjustable via PC software. Command Set is the same as the I2C-USB modem
Case for I2C-RS232-Modem 1
Finish machined case for I2C-RS232 modem 1 The holes for the LEDs and the cable entries are drilled. A piece of cable (50 cm) for the I2C-side, four screws for attaching the printed circuit board and two cable ties to secure the cables are included.
Case for I2C-RS232-Coupler
Finish machined case for I2C-RS232-Coupler The holes for the LEDs and the cable entries are drilled. A piece of cable (50 cm) for the I2C-side, four screws for attaching the printed circuit board and two cable ties to secure the cables are included.
Kit I2C-RS232 coupler
The I2C-coupler converts the V24 signals of the serial interface (RS232) in 5V signals for the I2C hardware. The kit includes all required components and the circuit board.
Kit I2C-RS232-Modem 1 / PC...
For communication to I2C commands as ASCII control sequences via the COM interface send and receive. The kit includes all required components and the circuit board. All prices include VAT plus shipping costs.Delivery time 2-3 daysPrice changes and errors excepted.
Kit I2C-USB-Modem PC...
With the I2C-USB mode, you can access I2C slaves via the PC. The kit includes all required components and the printed circuit board on which the FTDI SMD chip is already installed.