Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
The GPIO interface of the Raspberry PI is designed for 3.3V level. The I2C repeater raises the level of the SCL and SDA pins so that they are recognized clean 5V I2C slaves to 5V.
The kit contains the completely assembled PCB with all SMD components as well as the post connectors and 5-pole terminal strip. These can be ordered with either a fixed or pluggable terminal clamp.
Size of the circuit board 36 mm x 22 mm
Examples, see the blog post I2C-Pegelanpassung 3,3 / 5V für Raspberry PI
| 1 | PCB I2RPI ready soldered with all SMD components |
| 1 | Pin connector 26pin |
| 1 | terminal 5 pol. |
Manufacturer information
Responsible person for the EU
Horter & Kalb
Jürgen Horter
Klinikumallee 23
)5445 Bayreuth
mail@horter.de
Stacking Header 2 x 13 pin for I2C-Repeater Accessories for I2C-Repeater I2RPI+T-FG
Stacking Header 2 x 20 pin for I2C-Repeater Accessories for I2C-Repeater I2RPI+T-FG
Kit I2C analog input card 4 channel 18 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V +-10V +-2V or 0-20mA can be read.
Breakoutboard with I2C Calendar & Clock PCF 8583 The kit includes all required components and the circuit board.
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Stacking Header 2 x 20 pin for I2C-Repeater Accessories for I2C-Repeater I2RPI+T-FG
With the I2C-USB mode, you can access I2C slaves via the PC. The kit includes all required components and the printed circuit board on which the FTDI SMD chip is already installed.
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Kit I2C input card digital 8-bit 5-24V for DIN rail With the I2C input module you can read 8 digital signals up to 30V.
Set I2C connection cable 5pol Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AIN18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Kit I2C I2C-RS232-Modem 2 for DIN rail With this modemyou can control or read I2C slaves via the serial RS232 interface. The baud rate adjustable via PC software. Command Set is the same as the I2C-USB modem
Kit switching power supply control board 5V / 2,5A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Kit simulator module for 8 digital signals (8-bit) for DIN-rail mounting setpoint adjuster for eight digital signals for connection to the digital input card.
Simulator module for 5 alalog signals for DIN-rail mounting setpoint adjuster for five 0-10V analog signals for connection to the analogue input card
Precision measuring resistor 500 Ohm 0.1% 0.4W With this resistor, a current signal 0-20mA can be converted into a voltage signal 0-10V.Conversion 0-20mA signal in 0-10VConversion 4-20mA signal in 2-10VThe voltage can then be measured with the analog card.
Button for I2C-Repeater Accessories for I2C-Repeater I2RPI+T-FG
Level translating and I2C-bus repeater with PCA9517 The kit includes all required components and the circuit board.
I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Stacking Header 2 x 13 pin for I2C-Repeater Accessories for I2C-Repeater I2RPI+T-FG
Stacking Header 2 x 20 pin for I2C-Repeater Accessories for I2C-Repeater I2RPI+T-FG
connecting cable for I2C-Repeater Accessories for I2C-Repeater I2RPI+T-FG
