I2C-EEprom 512 Byte 4kBit DIL
CMOS serial EEPROM 512 Byte = 4 kBit
CMOS serial EEPROM 512 Byte = 4 kBit
In this section you will find interesting assemblies around the I2C bus.
These modules provide an interface to the I2C slave and a PC or other master example Raspberry-PI.
With the input cards digital signals can be read.
With the I2C-output digital consumer can be activated or switched.
With I2C analog cards, it is possible analog signals (voltage, current, temperature) can be read and analog devices can be controlled.
These modules all have a dimension of 42 mm x 63 mm.
They can be very easily installed with the Wago mounting frame for small boards on a DIN rail.
Control standard radio outlets via the I2C bus
Communicate via WLAN with the I2C modules
In this section you will find sensors that can be operated directly on the I2C bus.
With our Breakout Boards I2C modules can be tested without much effort.
With I2C switches you to bus segments individually.
With I2C multiplexers to slaves with the same address can be addressed on the bus.
I2C-Bus Level Translating between 3,3 V and 5 V
Here you will find I2C chip cards and readers or contacting units.
Our LCD displays can be addressed directly via the I2C-bus or RS232 serial interface.
I2C ICs and programmed PICs for our circuits and kits.
There are 108 products.
Active filters
CMOS serial EEPROM 512 Byte = 4 kBit
CMOS serial EEPROM 512 Byte = 4 kBit
Longer I2C bus wires with the P82B715 The kit includes all required components and the circuit board.
Longer I2C bus wires with the P82B715 The kit includes all required components and the circuit board.
CMOS serial EEPROM 1024 Byte = 8 kBit
CMOS serial EEPROM 1024 Byte = 8 kBit
4 analog inputs, 1 analog output 0 .10 V each The kit includes all required components and the circuit board.
4 analog inputs, 1 analog output 0 .10 V each The kit includes all required components and the circuit board.
CMOS serial EEPROM 2048 Byte = 16 kBit
CMOS serial EEPROM 2048 Byte = 16 kBit
Kit I2C digital input board 8-bit with optocoupler and latch All components including the PCB
Kit I2C digital input board 8-bit with optocoupler and latch All components including the PCB
TOSHIBA 8 Channel Common Source Power DMOS Array
TOSHIBA 8 Channel Common Source Power DMOS Array
CMOS serial EEPROM 4096 Byte = 32 kBit
CMOS serial EEPROM 4096 Byte = 32 kBit
I2C output board with transistor amplifiers 8- bit digital All components required for the I2C output board including 8 power transistors BD135 (invers) or BD136 (normal) Switching capacity max. 45V 1.5A
I2C output board with transistor amplifiers 8- bit digital All components required for the I2C output board including 8 power transistors BD135 (invers) or BD136 (normal) Switching capacity max. 45V 1.5A
Precision measuring resistor 500 Ohm 0.1% 0.4W With this resistor, a current signal 0-20mA can be converted into a voltage signal 0-10V.Conversion 0-20mA signal in 0-10VConversion 4-20mA signal in 2-10VThe voltage can then be measured with the analog card.
Precision measuring resistor 500 Ohm 0.1% 0.4W With this resistor, a current signal 0-20mA can be converted into a voltage signal 0-10V.Conversion 0-20mA signal in 0-10VConversion 4-20mA signal in 2-10VThe voltage can then be measured with the analog card.
I2C output board with relay output stages 8- bit digital All components required for the I2C output board including 8 single-line relay 5V with integr. Free-wheeling diode. Switching capacity max. 200V AC 15W
I2C output board with relay output stages 8- bit digital All components required for the I2C output board including 8 single-line relay 5V with integr. Free-wheeling diode. Switching capacity max. 200V AC 15W
I2C clock and calendar chip, based on a 2048-bit static CMOS RAMIt can be used as clock or RTC for counting pulses are used.
I2C clock and calendar chip, based on a 2048-bit static CMOS RAMIt can be used as clock or RTC for counting pulses are used.
I2C digital output board without amplifiers If you want to have mixed the output stages ( eg 2 Ralais and 6 transistors)You can order the basic components here and the output stages separately below in the shop
I2C digital output board without amplifiers If you want to have mixed the output stages ( eg 2 Ralais and 6 transistors)You can order the basic components here and the output stages separately below in the shop
Programmed GAL for our I2C Input card I2E-Bk
Programmed GAL for our I2C Input card I2E-Bk
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
I2C Analog-to-Digital Converter - ADC 18B delta-sigma ADC dual Ch 4sp
I2C Analog-to-Digital Converter - ADC 18B delta-sigma ADC dual Ch 4sp
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
Precision CMOS rail-to-rail input and output op amps
Precision CMOS rail-to-rail input and output op amps
Kit I2C-Repeater for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C-Repeater for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit I2C switch for DIN rail mounting The I2C switch it is possible to switch four I2C buses in any combination to a master. Also its possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit I2C switch for DIN rail mounting The I2C switch it is possible to switch four I2C buses in any combination to a master. Also its possible multiple I2C slaves with the same bus address to connect to the I2C bus.
8-Bit expander for I2C-Bus
8-Bit expander for I2C-Bus