Kit I2C Extender test board
Longer I2C bus wires with the P82B715
The kit includes all required components and the circuit board.
Description
With the I2C extender module, they can test the function of the module P82B715 without large amount of soldering.
With the extender longer I2C bus can be constructed according to the data of the P82B715.
To Take a look at the description AN255-02.pdf on page 11
At the other end sits back an extender of the "high-strung" level again brings back to standard I2C. Then can be interconnected as many slaves again.
Dimensions of the circuit board 40 x 30 mm.
Links:
More information here:: I2C-extender breakout board P82B715
Downloads
Partlist:
1 | circuit board I2EX-LP |
1 | I2C-Extender P 82B715 + IC socket 8 pin |
1 | Ceramic Capacitor 100 nF |
2 | terminal 4pol. |
2 | resistor 330 Ohm |
2 | resistor 4,7 k |
Specific References
- EAN13
- 4260404260639
Manufacturer information
GPSR information
Responsible person for the EU
Horter & Kalb
Jürgen Horter
Klinikumallee 23
)5445 Bayreuth
mail@horter.de
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Customers who bought this product also bought:
Kit I2C Output 24V 1A with...
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Kit I2C analog input module...
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Precision CMOS rail-to-rail...
Precision CMOS rail-to-rail input and output op amps
Kit I2C WLAN module for the...
Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.
Kit I2C digital input...
Digital I2C input card with optocouplers 8-bit 5-24V for DIN rail The I2C input module can be used to read 8 digital signals from 2.5V to 30V via the I2C bus. The inputs are galvanically isolated with optocouplers
Kit I2C analog output...
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
I2C-Repeater with switch...
I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C RS232 Modem 2 / PC...
Kit I2C I2C-RS232-Modem 2 for DIN rail With this modemyou can control or read I2C slaves via the serial RS232 interface. The baud rate adjustable via PC software. Command Set is the same as the I2C-USB modem
Kit I2C-Isolator test board...
Galvanic isolation of I2C buses with ADUM 1250 The kit includes all required components and the circuit board.
Kit I2C analog input 4...
Kit I2C analog input card 4 channel 18 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V +-10V +-2V or 0-20mA can be read.
Set I2C bus connector 5pol
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
16 other products in the same category:
Kit I2C WLAN module for the...
Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.
Kit I2C Buffer test board
I2C bus length up to 200m per data sheet with the P82B96. The kit includes all required components and the circuit board.
Kit I2C-Isolator test board...
Galvanic isolation of I2C buses with ADUM 1250 The kit includes all required components and the circuit board.
Kit I2C clock and calendar...
Breakoutboard with I2C Calendar & Clock PCF 8583 The kit includes all required components and the circuit board.
Kit I2C Output 24V AC / 1A...
Digital I2C output card for AC voltage 24V AC / 1Awith optocoupler and triac 8-bit for DIN rail With the I2C output card, 8 digital AC power consumers can be switched.
Kit I2C-Repeater for...
Kit I2C-Repeater for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C multiplexer...
Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit simulator module for 8...
Kit simulator module for 8 digital signals (8-bit) for DIN-rail mounting setpoint adjuster for eight digital signals for connection to the digital input card.
Kit I2C radio transmitter...
Kit I2C radio transmitter for DIN rail mounting this 433 MHz radio transmitter allows you remote-controlled electrical socket controlled via the I2C bus.
Kit I2C Master with Arduino...
I2C master kit with ARDUINO-UNO and optional W5500 LAN on DIN rail Compact I2C master with an "Arduino UNO" for the DIN rail. The module can be used to implement a variety of applications with the Arduino IDE or with Platform IO. For example: - I2C Modbus-TCP Server- I2C MQTT Client /...
Kit I2C output card with...
I2C output board with transistor amplifiers 8- bit digital All components required for the I2C output board including 8 power transistors BD135 (invers) or BD136 (normal) Switching capacity max. 45V 1.5A
Kit I2C-RS232 coupler
The I2C-coupler converts the V24 signals of the serial interface (RS232) in 5V signals for the I2C hardware. The kit includes all required components and the circuit board.
Kit I2C output card 8 bit...
I2C digital output board without amplifiers If you want to have mixed the output stages ( eg 2 Ralais and 6 transistors)You can order the basic components here and the output stages separately below in the shop
Kit I2C RS232 Modem 2 / PC...
Kit I2C I2C-RS232-Modem 2 for DIN rail With this modemyou can control or read I2C slaves via the serial RS232 interface. The baud rate adjustable via PC software. Command Set is the same as the I2C-USB modem
Kit I2C Input card 8 Bit
Kit I2C digital input board 8-bit with optocoupler and latch All components including the PCB
DIN-Mounting clip
Mounting clip for DIN rail Rittal SZ 2309.000 inkl. Screws M4 x 10