This 5V switching power supply control board I2C modules can be supplied with power.
The maximum input voltage range of the built-in switching regulator MC34063 is 40V and delivers up to 1.5 A.
In the control cabinet so that you can generate the 5V voltage for the I2C modules from the most existing 24V DC.
Size of the circuit board 42 mm x 63 mm
| 1 | circuit board I2HN_LP lead-free tinned with solder resist |
| 1 | Resistor 0,33 Ohm |
| 1 | Resistor 1,2 kOhm |
| 1 | Resistor 1,5 kOhm |
| 1 | Resistor 3,6 kOhm |
| 1 | LED green 3mm 2 mA |
| 1 | Rectifier diode 1N4007 |
| 1 | Schottky Diode 1N5819 |
| 1 | Elko 100 yF / 63V |
| 1 | Ceramic Capacitor 470 pF |
| 1 | Elko 470 yF 25V |
| 1 | MC34063AP switching regulator + IC-socket 8 pin |
| 1 | inductance 220 yH |
| 1 | fuse holder + fuse 1,0 A medium time-lag |
| 2 | terminal 2 pol. |
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
I2C bus length up to 200m per data sheet with the P82B96. The kit includes all required components and the circuit board.
Set I2C connection cable 5pol Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AIN18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Level translating and I2C-bus repeater with PCA9517 The kit includes all required components and the circuit board.
Digital I2C input card with optocouplers 8-bit 5-24V for DIN rail The I2C input module can be used to read 8 digital signals from 2.5V to 30V via the I2C bus. The inputs are galvanically isolated with optocouplers
I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Kit switching power supply control board 3,3V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Kit I2C I2C-RS232-Modem 2 for DIN rail With this modemyou can control or read I2C slaves via the serial RS232 interface. The baud rate adjustable via PC software. Command Set is the same as the I2C-USB modem
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
Kit I2C input card digital 8-bit 5-24V for DIN rail With the I2C input module you can read 8 digital signals up to 30V.
I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C ARDUINO module for "Arduino Pro Micro" on DIN rail Put the "ARDUINO Pro Micro" on the top-hat rail and write your own applications as an I2C master or I2C slave.
Set I2C connection cable 5pol Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AIN18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Simulator Panel Voltmeter Module 6 analog measurements 0-30V Digital display for six 0-30V analog values for connection to the analog output card.
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.
Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit I2C analog input card 4 channel 18 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V +-10V +-2V or 0-20mA can be read.
