Kit I2C digital input Module
Kit I2C input card digital 8-bit 5-24V for DIN rail With the I2C input module you can read 8 digital signals up to 30V.
setpoint adjuster for eight digital signals for connection to the digital input card.
With the 8 toggle switches, you can specify the signals to the PLC input card. Depending on a Low Current LED (2 mA) shows the current status of the input.
Supply voltage: 5-12V
Dimension of the printed circuit board 42 mm x 63 mm
1 | circuit board SIM-DI_LP lead-free tinned with solder resist |
8 | toggle switch |
2 | Resistor network 4x 4,7k for 12V / 4x 10k for 24V |
8 | LED green 2mA |
1 | terminal 2 pol. fix or plug in |
1 | terminal 8 pol. fix or plug in |
Kit I2C input card digital 8-bit 5-24V for DIN rail With the I2C input module you can read 8 digital signals up to 30V.
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Kit I2C digital input board 8-bit with optocoupler and latch All components including the PCB
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Stacking Header 2 x 20 pin for I2C-Repeater Accessories for I2C-Repeater I2RPI+T-FG
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Simulator module for 5 alalog signals for DIN-rail mounting setpoint adjuster for five 0-10V analog signals for connection to the analogue input card
Kit I2C analog input card 4 channel 18 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V +-10V +-2V or 0-20mA can be read.
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
With the I2C-USB mode, you can access I2C slaves via the PC. The kit includes all required components and the printed circuit board on which the FTDI SMD chip is already installed.
I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Finish machined case for I2C-USB modem. The holes for the LEDs and the power supply are drilled. Furthermore millings for the tub and plug the USB connector are made on both sides.
Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Set I2C connection cable 5pol Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AIN18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Mounting clip for DIN rail Rittal SZ 2309.000 inkl. Screws M4 x 10
Digital I2C output card for AC voltage 24V AC / 1Awith optocoupler and triac 8-bit for DIN rail With the I2C output card, 8 digital AC power consumers can be switched.
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Simulator module for 5 alalog signals for DIN-rail mounting setpoint adjuster for five 0-10V analog signals for connection to the analogue input card
Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.
Kit I2C ARDUINO module for "Arduino Pro Micro" on DIN rail Put the "ARDUINO Pro Micro" on the top-hat rail and write your own applications as an I2C master or I2C slave.
Kit switching power supply control board 3,3V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Kit I2C I2C-RS232-Modem 2 for DIN rail With this modemyou can control or read I2C slaves via the serial RS232 interface. The baud rate adjustable via PC software. Command Set is the same as the I2C-USB modem
Kit switching power supply control board 3,3V 5V 9V 10V 15V 24V / 2,5A for DIN-Rail This switched-mode power supply board can be used to supply the I2C modules or other devices with power.
I2C pulse counter kit with PCF8583 and optocoupler 2-channel counter for fast pulses
Kit I2C input card digital 8-bit 5-24V for DIN rail With the I2C input module you can read 8 digital signals up to 30V.
Kit switching power supply control board 5V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.