Case for I2C USB modem
Finish machined case for I2C-USB modem. The holes for the LEDs and the power supply are drilled. Furthermore millings for the tub and plug the USB connector are made on both sides.
With the I2C-USB mode, you can access I2C slaves via the PC.
The kit includes all required components and the printed circuit board on which the FTDI SMD chip is already installed.
More information and program examples here: I2C-USB-Modem.
1 | I2UM-LP circuit board I2C-USB-Modem |
4 | Resistor 270 Ohm |
3 | Resistor 4,7 kOhm |
1 | LED 3mm red |
1 | LED 3mm yellow |
1 | LED 3mm green |
2 | Ceramic Capacitor 27 pF |
2 | Ceramic Capacitor 47 pF |
1 | Ceramic Capacitor 100 nF |
1 | Elko 47yF |
1 | Quarz 10 MHz |
1 | I2UM-PIC PIC18F1320P (programmed) |
1 | IC socket 18 pin |
1 | FT232RL (soldered) |
2 | pin connectors 3 pol and Jumper |
1 | terminal 5pol. |
1 | power socket |
1 | USB-terminal plug |
1 | USB-cable with A-Plugs on both side |
Finish machined case for I2C-USB modem. The holes for the LEDs and the power supply are drilled. Furthermore millings for the tub and plug the USB connector are made on both sides.
Plug-in switching power supply 5 V / 2 A In: 100-240V / 50-60 HzOut: 5 V / 2 A Dimensions (LxWxH): 80 x 32 x 42 mm + connector contacts Connecting cable 1.5 m with 5.5 pin barrel connectors diameter 2,1 mm center positive.
International Power Supply 5 V / 1200 mA = 1.2A Country adapter EU / GB / AU / US In: 100-240V / 50-60 Hz, 0,3 A maxOut: 5 V / 1,2 A Dimensions (LxWxH): 62 x 32 x 41 mm + connector contacts Connecting cable 1.5 m with barrel connectors Ø external 5,5 mm Øinternal 2,1 mm center positive.
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Finish machined case for I2C-RS232-Coupler The holes for the LEDs and the cable entries are drilled. A piece of cable (50 cm) for the I2C-side, four screws for attaching the printed circuit board and two cable ties to secure the cables are included.
Finish machined case for I2C-USB modem. The holes for the LEDs and the power supply are drilled. Furthermore millings for the tub and plug the USB connector are made on both sides.
Finish machined case for I2C-RS232 modem 1 The holes for the LEDs and the cable entries are drilled. A piece of cable (50 cm) for the I2C-side, four screws for attaching the printed circuit board and two cable ties to secure the cables are included.
Kit I2C I2C-RS232-Modem 2 for DIN rail With this modemyou can control or read I2C slaves via the serial RS232 interface. The baud rate adjustable via PC software. Command Set is the same as the I2C-USB modem
For communication to I2C commands as ASCII control sequences via the COM interface send and receive. The kit includes all required components and the circuit board. All prices include VAT plus shipping costs.Delivery time 2-3 daysPrice changes and errors excepted.
The I2C-coupler converts the V24 signals of the serial interface (RS232) in 5V signals for the I2C hardware. The kit includes all required components and the circuit board.