Set I2C bus connector 5pol

M3 adhesive base and screw M3 x 6 mm

Kit I2C ARDUINO module for "Arduino Pro Micro" on DIN rail  Put the "ARDUINO Pro Micro" on the top-hat rail and write your own applications as an I2C master or I2C slave.

Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.

Digital I2C output card with optocouplers8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The output driver TBD62783APG switches a positive voltage up to 30V.

M3 adhesive base with thread M3

Precision CMOS rail-to-rail input and output op amps

8-Bit expander for I2C-Bus

Digital I2C output card for AC voltage 24V AC / 1Awith optocoupler and triac 8-bit for DIN rail With the I2C output card, 8 digital AC power consumers can be switched.

Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL

I2C pulse counter kit with PCF8583 and optocoupler 2-channel counter for fast pulses

Finish machined case for I2C-USB modem. The holes for the LEDs and the power supply are drilled. Furthermore millings for the tub and plug the USB connector are made ​​on both sides.

Kit switching power supply control board 3,3V 5V 9V 10V 15V 24V / 2,5A for DIN-Rail This switched-mode power supply board can be used to supply the I2C modules or other devices with power.

8-Bit expander for I2C-Bus

Mounting clip for DIN rail Rittal SZ 2309.000 inkl. Screws M4 x 10

I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL

Power cord for AC-Adapter black - length 1,4 m or 1,8 mCable cross-section   3x 0.75 mm² Load limit  6 A 

Kit I2C analog input card 8 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.

Kit switching power supply control board 3,3V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.

Simulator Panel Voltmeter Module 6 analog measurements 0-30V Digital display for six 0-30V analog values for connection to the analog output card.

Digital I2C output card for AC voltage 24V AC / 1Awith optocoupler and triac 8-bit for DIN rail With the I2C output card, 8 digital AC power consumers can be switched.

Kit switching power supply control board 5V / 2,5A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.

Kit simulator module for 8 digital signals (8-bit) for DIN-rail mounting setpoint adjuster for eight digital signals for connection to the digital input card.

Mounting clip for DIN rail Rittal SZ 2309.000 inkl. Screws M4 x 10

Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.

Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL

Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.

Simulator module for 5 alalog signals for DIN-rail mounting setpoint adjuster for five 0-10V analog signals for connection to the analogue input card

I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL

Kit I2C input card digital 8-bit 5-24V for DIN rail With the I2C input module you can read 8 digital signals up to 30V.

Kit I2C-Repeater for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL

Digital I2C output card with optocouplers8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The output driver TBD62783APG switches a positive voltage up to 30V.

Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.