With the I2C input module you can read 8 digital signals up to 30V.
With the I2C input module 8 digital signals can, for example, are read by switches or sensors.
The signal states are displayed on eight low-current LEDs, the HIGH level is detected from 4V.
Changes a signal at an input will be signaled at a red LED and pulled the INT signal to LOW.
The I2C modem detects this signal change and may possibly also automatically retrieve all input cards.
Size of the circuit board 42 mm x 63 mm
For more information about this product can be found on the product page i2c-input-modul.
| 1 | circuit board I2HE_LP lead-free tinned with solder resist |
| 1 | Resistor 1,5 kOhm |
| 2 | Resistor 4,7 kOhm |
| 2 | Resistor 10 kOhm |
| 2 | Resistor network 4x 4,7k |
| 1 | Resistor network 8x 1,5k |
| 2 | Resistor network 8x 4,7k |
| 8 | LED 3mm 2mA green |
| 1 | LED 3mm 2mA red |
| 1 | Ceramic Capacitor 100 nF |
| 2 | NPN-Transistor BC546A |
| 1 | PCF8574P oder PCF8574A + IC socket 16 pin |
| 1 | ULN2803 Darlington-Array + IC socket 18 pin |
| 3 | pin connectors 3 pol and Jumper |
| 1 | terminal 5 pol. |
| 1 | terminal 10 pol. |
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Kit I2C-Repeater for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C analog input card 4 channel 18 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V +-10V +-2V or 0-20mA can be read.
Set I2C connection cable 5pol Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AIN18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Simulator module for 5 alalog signals for DIN-rail mounting setpoint adjuster for five 0-10V analog signals for connection to the analogue input card
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
I2C pulse counter kit with PCF8583 and optocoupler 2-channel counter for fast pulses
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.
I2C Analog-to-Digital Converter - ADC 18B delta-sigma ADC dual Ch 4sp
Plug-in switching power supply 5 V / 2 A In: 100-240V / 50-60 HzOut: 5 V / 2 A Dimensions (LxWxH): 80 x 32 x 42 mm + connector contacts Connecting cable 1.5 m with 5.5 pin barrel connectors diameter 2,1 mm center positive.
Mounting clip for DIN rail Rittal SZ 2309.000 inkl. Screws M4 x 10
Kit I2C ARDUINO module for "Arduino Pro Micro" on DIN rail Put the "ARDUINO Pro Micro" on the top-hat rail and write your own applications as an I2C master or I2C slave.
Kit I2C-Repeater for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
Mounting clip for DIN rail Rittal SZ 2309.000 inkl. Screws M4 x 10
Simulator module for 5 alalog signals for DIN-rail mounting setpoint adjuster for five 0-10V analog signals for connection to the analogue input card
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Digital I2C input card with optocouplers 8-bit 5-24V for DIN rail The I2C input module can be used to read 8 digital signals from 2.5V to 30V via the I2C bus. The inputs are galvanically isolated with optocouplers
Digital I2C output card for AC voltage 24V AC / 1Awith optocoupler and triac 8-bit for DIN rail With the I2C output card, 8 digital AC power consumers can be switched.
Kit switching power supply control board 5V / 2,5A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Kit I2C radio transmitter for DIN rail mounting this 433 MHz radio transmitter allows you remote-controlled electrical socket controlled via the I2C bus.
Kit I2C switch for DIN rail mounting The I2C switch it is possible to switch four I2C buses in any combination to a master. Also its possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit switching power supply control board 5V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit I2C I2C-RS232-Modem 2 for DIN rail With this modemyou can control or read I2C slaves via the serial RS232 interface. The baud rate adjustable via PC software. Command Set is the same as the I2C-USB modem
I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit simulator module for 8 digital signals (8-bit) for DIN-rail mounting setpoint adjuster for eight digital signals for connection to the digital input card.
