Kit I2C-Isolator test board ADUM1250

I2C Bus Buffer for longer lines at the I2C bus

Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.

I2C bus length up to 200m per data sheet with the P82B96. The kit includes all required components and the circuit board.

Kit I2C analog input card 4 channel 18 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V +-10V +-2V or 0-20mA can be read.

Set I2C connection cable 5pol Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AIN18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...

Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL

Digital I2C input card with optocouplers 8-bit 5-24V for DIN rail The I2C input module can be used to read 8 digital signals from 2.5V to 30V via the I2C bus. The inputs are galvanically isolated with optocouplers

Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...

Resistor network for I2EOK 9 pin 8 resistors

Digital I2C output card with optocouplers8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The output driver TBD62783APG switches a positive voltage up to 30V.

Kit switching power supply control board 3,3V 5V 9V 10V 15V 24V / 2,5A for DIN-Rail This switched-mode power supply board can be used to supply the I2C modules or other devices with power.

Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits

Button for I2C-Repeater Accessories for I2C-Repeater I2RPI+T-FG

Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.

Digital I2C output card with optocouplers8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The output driver TBD62783APG switches a positive voltage up to 30V.

Longer I2C bus wires with the P82B715 The kit includes all required components and the circuit board.

Kit I2C I2C-RS232-Modem 2 for DIN rail With this modemyou can control or read I2C slaves via the serial RS232 interface. The baud rate adjustable via PC software. Command Set is the same as the I2C-USB modem

I2C pulse counter kit with PCF8583 and optocoupler 2-channel counter for fast pulses

Rod antenna for 433 MHz transmitter With this antenna you increase the range of I2C radio transmitter.

For communication to I2C commands as ASCII control sequences via the COM interface send and receive. The kit includes all required components and the circuit board. All prices include VAT plus shipping costs.Delivery time 2-3 daysPrice changes and errors excepted.

Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL

4 analog inputs, 1 analog output 0 .10 V each  The kit includes all required components and the circuit board.

Rod antenna for 433 MHz transmitter This antenna can be mounted outside the switchbox.

I2C output board with transistor amplifiers 8- bit digital All components required for the I2C output board including 8 power transistors BD135 (invers) or BD136 (normal) Switching capacity max. 45V 1.5A

Kit I2C switch for DIN rail mounting The I2C switch it is possible to switch four I2C buses in any combination to a master. Also its possible multiple I2C slaves with the same bus address to connect to the I2C bus.

Kit switching power supply control board 3,3V 5V 9V 10V 15V 24V / 2,5A for DIN-Rail This switched-mode power supply board can be used to supply the I2C modules or other devices with power.

Kit I2C ARDUINO module for "Arduino Pro Micro" on DIN rail  Put the "ARDUINO Pro Micro" on the top-hat rail and write your own applications as an I2C master or I2C slave.

Kit I2C-Repeater for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL

Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.