Mounting frame
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
This switched-mode power supply board can be used to supply the I2C modules or other devices with power.
The maximum input voltage range of the built-in switching regulator LM 2576 is 40V and delivers up to 3 A.
In the control cabinet you can thus generate further voltages from the most existing 24V DC.
Size of the circuit board 42 mm x 63 mm
Data Sheet Shematic Diagram data sheet LM2576
1 | circuit board I2HN3_LP lead-free tinned with solder resist |
1 | Resistors according to table in the data sheet |
1 | LED green 3mm 2 mA |
1 | Rectifier diode 1N4007 |
1 | Schottky Diode SB360 |
1 | Elko 100 yF / 63V |
1 | Elko 1000 yF / 25V |
1 | LM 2576 3,3 5 12 15 oder ADJ |
1 | heatsink + screw M3x16 Spacing roller Ø 3 x 8 mm |
1 | inductance 100 yH / 3,2 A |
1 | fuse holder + fuse 2,5 A medium time-lag |
2 | terminal 2 pol. |
Uout | IC1 | R1 (1%) | R2 (1%) | R3 = Rv LED (5%) |
3,3V | LM 2576 T3,3 | -- | -- | 1,5 kΩ |
5V | LM 2576 T5 | -- | -- | 1,5 kΩ |
9V | LM2576 T-ADJ | 560 Ω | 3,6 kΩ | 3,6 kΩ |
10V | LM2576 T-ADJ | 590 Ω | 4,3 kΩ0 | 3,6 kΩ |
12 | LM 2576 T12 | -- | -- | 3,6 kΩ |
15V | LM 2576 T15 | -- | -- | 3,6 kΩ |
24V | LM2576 T-ADJ | 270 Ω | 4,99 kΩ | 11 kΩ |
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Set I2C connection cable 5pol Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AIN18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Kit I2C analog input card 5 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
Digital I2C input card with optocouplers 8-bit 5-24V for DIN rail The I2C input module can be used to read 8 digital signals from 2.5V to 30V via the I2C bus. The inputs are galvanically isolated with optocouplers
connecting cable for I2C-Repeater Accessories for I2C-Repeater I2RPI+T-FG
Kit I2C analog input card 8 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit I2C I2C-RS232-Modem 2 for DIN rail With this modemyou can control or read I2C slaves via the serial RS232 interface. The baud rate adjustable via PC software. Command Set is the same as the I2C-USB modem
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Kit I2C output card digital 8-bit 5-24V for DIN rail With the I2C output card 8 digital loads can be switched. The output driver turns UDN2981 a positive voltage up to 30V.
Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit switching power supply control board 3,3V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Kit I2C-Repeater for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit switching power supply control board 5V / 2,5A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Kit I2C switch for DIN rail mounting The I2C switch it is possible to switch four I2C buses in any combination to a master. Also its possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit I2C ARDUINO module for "Arduino Pro Micro" on DIN rail Put the "ARDUINO Pro Micro" on the top-hat rail and write your own applications as an I2C master or I2C slave.
Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Kit switching power supply control board 5V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Simulator Panel Voltmeter Module 6 analog measurements 0-30V Digital display for six 0-30V analog values for connection to the analog output card.
Kit I2C I2C-RS232-Modem 2 for DIN rail With this modemyou can control or read I2C slaves via the serial RS232 interface. The baud rate adjustable via PC software. Command Set is the same as the I2C-USB modem
Mounting clip for DIN rail Rittal SZ 2309.000 inkl. Screws M4 x 10
Kit I2C analog input card 4 channel 18 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V +-10V +-2V or 0-20mA can be read.
Simulator module for 5 alalog signals for DIN-rail mounting setpoint adjuster for five 0-10V analog signals for connection to the analogue input card