Mounting frame
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
With the I2C output card, 8 digital consumers can be switched.
The output driver TBD62783APG switches a positive voltage up to 30V.
With the I2C output card, 8 digital consumers can be switched.
The output driver TBD62783APG switches a positive voltage up to 30V.
The outputs are galvanically isolated from the I2C bus using optocouplers.
The circuit uses the negative logic because the I2C port expansion module PCF8574 switches on all outputs at voltage.
When controlling, only the desired bit pattern has to be inverted. Or subtract from the 255 desired output value before transferring it to the output card.
Dimension of the circuit board 42 mm x 63 mm
1 | circuit board IAOK_LP lead-free tinned with solder resist |
2 | Resistor network 8x 1,5k |
1 | Resistor network 8x 10k |
8 | LED 3mm 2mA green |
1 | Ceramic Capacitor 100 nF |
1 | PCF8574P or PCF8574A + IC socket 16 pin |
1 | TBD62783APG + IC socket 18 pin |
2 | Opto coupler TLP293-4 soldered |
3 | pin connectors 3 pol and Jumper |
1 | terminal 4 pol. |
1 | terminal 10 pol. |
Manufacturer information
Responsible person for the EU
Horter & Kalb
Jürgen Horter
Klinikumallee 23
)5445 Bayreuth
mail@horter.de
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Set I2C bus connector 5-pin Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AI18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Set I2C connection cable 5pol Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AIN18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
I2C-Repeater for Raspberry PI finished Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
With the I2C-USB mode, you can access I2C slaves via the PC. The kit includes all required components and the printed circuit board on which the FTDI SMD chip is already installed.
Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit switching power supply control board 5V / 2,5A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Digital I2C output card with power transistors8-bit 5-24V for DIN rail With the I2C output card, 8 digital consumers can be switched.The power transistor BD676 can switch 40V 1A.
Longer I2C bus wires with the P82B715 The kit includes all required components and the circuit board.
Kit I2C input card digital 8-bit 5-24V for DIN rail With the I2C input module you can read 8 digital signals up to 30V.
I2C pulse counter kit with PCF8583 and optocoupler 2-channel counter for fast pulses
connecting cable for I2C-Repeater Accessories for I2C-Repeater I2RPI+T-FG
W5500 TCP/IP Ethernet module for the I2C master with Arduino UNO
Kit I2C analog input card 8 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
Kit I2C-Repeater with switch for Raspberry PI Level Translating from 3.3 V to 5 V for GPIO ports SDA and SCL
Stacking Header 2 x 13 pin for I2C-Repeater Accessories for I2C-Repeater I2RPI+T-FG
Mounting frame for DIN rail Set WAGO Mounting base for our I2C rails kits
Kit I2C input card digital 8-bit 5-24V for DIN rail With the I2C input module you can read 8 digital signals up to 30V.
Simulator Panel Voltmeter Module 6 analog measurements 0-30V Digital display for six 0-30V analog values for connection to the analog output card.
Kit switching power supply control board 3,3V / 1A for DIN rail This 5V switching power supply control board I2C modules can be supplied with power.
Kit I2C analog output card 4 channel 10 bit for DIN-rail With the I2C analog output card 4 analog control signals of 0-10 V can be output.
I2C master kit with ARDUINO-UNO and optional W5500 LAN on DIN rail Compact I2C master with an "Arduino UNO" for the DIN rail. The module can be used to implement a variety of applications with the Arduino IDE or with Platform IO. For example: - I2C Modbus-TCP Server- I2C MQTT Client /...
Mounting clip for DIN rail Rittal SZ 2309.000 inkl. Screws M4 x 10
I2C pulse counter kit with PCF8583 and optocoupler 2-channel counter for fast pulses
Kit I2C radio transmitter for DIN rail mounting this 433 MHz radio transmitter allows you remote-controlled electrical socket controlled via the I2C bus.
Set I2C connection cable 5pol Accessories for I2C bus modules I2EOK, I2AOK, I2AT, I2AIN18 Not suitable for I2HE, I2AH, I2HAE, I2HAA ...
Kit I2C switch for DIN rail mounting The I2C switch it is possible to switch four I2C buses in any combination to a master. Also its possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit I2C analog input card 8 channel 10 bit for DIN-rail With the I2C analog input card 5 analog signals of 0-10 V can be read.
Kit simulator module for 8 digital signals (8-bit) for DIN-rail mounting setpoint adjuster for eight digital signals for connection to the digital input card.
Digital I2C output card for AC voltage 24V AC / 1Awith optocoupler and triac 8-bit for DIN rail With the I2C output card, 8 digital AC power consumers can be switched.
Kit I2C multiplexer for DIN rail mounting With the I2C multiplexer, it is possible multiple I2C slaves with the same bus address to connect to the I2C bus.
Kit I2C WLAN module for the WEMOS-D1 on DIN rail With this WLAN module you can control I2C modules via the WLAN.